Stainless Steel Sheet Thickness & Tolerance Guide

Tolérance d'épaisseur de tôle d'acier inoxydable définit dans quelle mesure l'épaisseur réelle d'une tôle d'acier inoxydable peut différer de son épaisseur spécifiée tout en respectant la norme de fabrication applicable.

Pour les acheteurs qui s'approvisionnent en tôles d'acier inoxydable 304, 316L, 201 ou autres, il est essentiel de comprendre ces tolérances. Une tôle commandée à 1,00 mm ne mesure pas forcément exactement 1.000 mm en tout point. La variation autorisée dépend de la norme du produit, du processus de laminage, de l'épaisseur, de la largeur et de la classe de tolérance spécifiées.

Il n’existe pas de tolérance d’épaisseur universelle pour toutes les tôles d’acier inoxydable. ASTM A480/A480M, ISO 9445 et d'autres normes définissent différentes exigences pour différents produits.

Ce guide explique les tableaux d'épaisseur des tôles d'acier inoxydable, les conversions de jauges, les tolérances ASTM et ISO, les produits laminés à froid par rapport aux produits laminés à chaud, les procédures de mesure et les informations que les acheteurs doivent inclure dans un bon de commande international.

Stainless Steel Sheet Thickness & Tolerance at a Glance

Avant de sélectionner une tôle en acier inoxydable, il est important de distinguer les dimensions spécifiées des variations de fabrication acceptables.

Quick Answers for Stainless Steel Buyers

What is the standard thickness tolerance for a 1 mm stainless steel sheet?

There is no single answer. You must identify the applicable standard, product type, width, and tolerance class.

Does 304 stainless steel have a different thickness tolerance from 316L?

Not necessarily. When both are ordered under the same applicable dimensional standard and equivalent product conditions, the same dimensional tolerance requirements may apply.

What is 16 gauge stainless steel thickness?

A commonly used U.S. stainless steel gauge chart gives 16 gauge as 0.0625 inches, approximately 1.59 mm.

Which standard covers stainless steel sheet tolerances?

ASTM A480/A480M is a principal ASTM reference for flat-rolled stainless steel products. ISO 9445-2 is a principal reference for continuously cold-rolled stainless steel wide strip and sheet/plate within its defined scope.

What Is Stainless Steel Sheet Thickness Tolerance?

Thickness tolerance is the permitted difference between the specified sheet thickness and the actual measured thickness.

The tolerance may be symmetrical or asymmetrical.

A symmetrical tolerance allows variation in both directions by the same amount.

An asymmetrical tolerance allows different positive and negative deviations.

Nominal Thickness vs. Actual Thickness

Consider a hypothetical stainless steel sheet specification:

1.00 mm ±0.05 mm

In this example:

• Specified thickness: 1.00 mm
• Maximum permitted thickness: 1.05 mm
• Minimum permitted thickness: 0.95 mm
• Upper deviation: +0.05 mm
• Lower deviation: -0.05 mm

Important: The ±0.05 mm value is an illustrative example, not a universal tolerance for 1 mm stainless steel sheets.

The actual permissible values must be obtained from the applicable specification.

How to Calculate Thickness Deviation

The basic calculation is:

Thickness Deviation = Actual Thickness − Specified Thickness

Par exemple:

Specified thickness = 1.00 mm

Measured thickness = 0.97 mm

Thickness deviation = 0.97 − 1.00 = -0.03 mm

To determine whether the sheet is acceptable, compare the result with the specified tolerance limits.

If the permitted lower deviation is -0.05 mm, this measurement is within that illustrative tolerance.

However, if the permitted lower deviation is only -0.02 mm, the measurement would not meet that requirement.

What Is Minimum Guaranteed Thickness?

Some buyers require a minimum actual thickness rather than a conventional symmetrical tolerance.

For example, a project may require:

Actual thickness must not be less than 1.00 mm.

This is different from ordering a nominal 1.00 mm sheet with negative thickness tolerance.

The supplier may need to select a different nominal thickness or agree to a special tolerance arrangement to satisfy the minimum-thickness requirement.

When minimum thickness is critical for structural strength, pressure resistance, or component assembly, the purchase order should state it explicitly.

Standard Stainless Steel Sheet Thickness Chart

Stainless steel sheets are available in many nominal thicknesses.

Commonly specified metric thicknesses include:

The applications listed are illustrative, not engineering thickness recommendations.

A 1.5 mm sheet may be appropriate for one fabricated component but completely unsuitable for another component with different loading, span, or environmental conditions.

Common Stainless Steel Sheet Sizes

International stainless steel buyers frequently request dimensions such as:

Actual availability depends on stainless steel grade, manufacturing route, thickness, and supplier capabilities.

These dimensions are nominal purchasing formats, not guaranteed tolerances.

Are Stainless Steel Sheet and Plate the Same?

Sheet and plate are both flat-rolled products, but they are not always manufactured or specified using the same standards.

Cold-rolled sheet is commonly produced from continuously rolled strip.

Heavy stainless steel plate may be manufactured through different hot-rolling routes.

Therefore, a tolerance table intended for cold-rolled sheet cannot automatically be applied to hot-rolled quarto plate.

Tableau des jauges en acier inoxydable : jauge en mm et en pouces

La jauge est une méthode traditionnelle d’identification de l’épaisseur de la tôle.

Cependant, la jauge n’est pas une mesure métrique directe.

Différents matériaux de tôlerie peuvent utiliser différentes conventions de jauge.

Une tôle d'acier inoxydable de calibre 16 n'a pas nécessairement la même épaisseur qu'une tôle d'acier au carbone ou d'aluminium de calibre 16.

Tableau de conversion d'épaisseur de jauge en acier inoxydable

Ce tableau présente les équivalents nominaux des jauges en acier inoxydable américains couramment utilisés. Les chiffres en millimètres sont arrondis. Les numéros de jauge ne définissent pas la tolérance de fabrication et les conventions des fournisseurs doivent être confirmées.

Qu'est-ce que l'acier inoxydable de calibre 16 en mm ?

L’acier inoxydable de calibre 16 est généralement répertorié comme :

00,0625 pouces = 1,5875 mm

Arrondi à deux décimales :

Calibre 16 ≈ 1,59 mm

Cependant, spécifier 1,50 mm ou 1,60 mm n’équivaut pas nécessairement à commander du calibre 16.

Si les dimensions de fabrication sont critiques, indiquez l’épaisseur décimale requise.

Jauge en acier inoxydable vs jauge en acier au carbone

Un même numéro de calibre peut correspondre à des épaisseurs nominales différentes.

Par exemple:

This difference matters when converting designs between materials.

If a component drawing was originally prepared for 16-gauge carbon steel, using 16-gauge stainless steel without checking the dimensions may change the actual sheet thickness.

That can affect bending allowances, part fit, clearances, and assembly.

Best Practice for International Purchasing

For export orders, specify thickness in:

• Millimeters, or
• Decimal inches

Gauge may be included as a secondary reference, but it should not be the only thickness requirement.

Par exemple:

304 Stainless Steel Sheet, 1.50 mm, 2B Finish

is more explicit than:

304 Stainless Steel Sheet, 16 Gauge

ASTM A480 Stainless Steel Thickness Tolerances

ASTM A480/A480M is one of the most important references for stainless steel sheet and plate procurement.

It provides general requirements applicable to specified flat-rolled stainless steel products, including dimensional tolerances.

ASTM A240 vs. ASTM A480

These two standards serve different functions.

ASTM A240 covers matters such as chemical composition and mechanical properties.

ASTM A480 provides general requirements that apply in conjunction with relevant product standards, unless superseded by the applicable requirements.

For purchasing 304 stainless steel sheet, both may be relevant.

ASTM A480 vs. ASTM A480M

This distinction is especially important for international orders.

ASTM A480/A480M contient des systèmes de tolérance dimensionnelle distincts en pouces-livres et SI.

La norme précise que les systèmes doivent être utilisés indépendamment.

Un acheteur ne doit pas simplement convertir le tableau de tolérance pouces-livres en millimètres et présenter ce résultat comme la tolérance officielle de l'A480M.

Pour les achats métriques, les exigences SI applicables doivent être utilisées.

Qu'est-ce qui détermine la tolérance d'épaisseur ASTM ?

Les facteurs pertinents peuvent inclure :

• Épaisseur spécifiée
• Type de produit
• Largeur de feuille ou de plaque
• État laminé à froid ou à chaud
• Tableau dimensionnel applicable
• État des bords
• Exigences particulières convenues

Certains systèmes de tolérance des tôles laminées à chaud utilisent des écarts supérieurs et inférieurs asymétriques.

Par conséquent, toutes les tolérances d’épaisseur de l’acier inoxydable ne sont pas exprimées avec ± la même valeur.

Exemple d'approvisionnement ASTM A480

A purchasing specification might state:

304 / UNS S30400 Stainless Steel Sheet

ASTM A240/A240M and applicable ASTM A480/A480M requirements

Thickness: 1.00 mm

Largeur : 1219 mm

Longueur : 2438 mm

Terminer : 2B

The buyer should then confirm which exact dimensional requirements apply to the specified product and whether any additional minimum-thickness requirement is necessary.

If a tighter thickness range is required, it must be agreed with the supplier and documented in the purchase order.

ISO 9445 Stainless Steel Thickness Tolerances

ISO 9445 provides dimensional tolerance requirements for continuously cold-rolled stainless steel products.

The two relevant parts distinguish narrow and wide strip products.

ISO 9445-2 covers specified cold-rolled stainless steel wide strip and sheet/plate with thicknesses from 0.30 mm to 8.00 mm and rolling widths from 600 mm to 2100 mm.

ISO 9445-2 Method A vs. Method B

ISO 9445-2 provides two methods for wide-strip thickness tolerances.

The methods use different tolerance tables and measurement positions.

Under the published BSSA summary:

Method A

• Thickness measurement more than 20 mm from slit edges
• Thickness measurement more than 30 mm from mill edges

Method B

• Thickness measurement more than 15 mm from slit edges
• Thickness measurement more than 25 mm from mill edges

These requirements should not be replaced with a generic instruction to measure a fixed distance from every edge.

ISO 9445-2 Method A Thickness Tolerance Chart

The following table is an extract of normal tolerance values for cold-rolled wide strip, Method A, nominal width greater than 1000 mm and less than 1300 mm.

All dimensions are in millimeters.

These values apply only to the stated Method A, width band, and normal tolerance conditions. They are not a universal stainless steel tolerance chart. For thickness values exactly at table boundaries, other width bands, or special tolerances, consult the complete applicable standard.

Example: 1.10 mm Thick, 1219 mm Wide Sheet

Considérer:

• Specified thickness: 1.10 mm
• Nominal width: 1219 mm
• Product: Continuously cold-rolled stainless steel wide strip/sheet
• Standard: ISO 9445-2
• Method: A
• Tolerance class: Normal

This falls within the thickness band:

1.00 < t < 1.20 mm

and width band:

1000 < w < 1300 mm

The normal thickness tolerance is:

±0.07 mm

Donc:

Minimum thickness = 1.10 − 0.07 = 1.03 mm

Maximum thickness = 1.10 + 0.07 = 1.17 mm

Measurements must be taken in accordance with the applicable standard’s location requirements.

What If Special Thickness Tolerance Is Required?

ISO 9445 also provides special tolerance values for certain products and thickness ranges.

For the same 1.10 mm and 1219 mm Method A example, the published special tolerance value is ±0.045 mm.

This demonstrates why buyers must identify both the standard and the required tolerance level.

A special tolerance should not be assumed automatically.

It should be requested and confirmed at the quotation and purchase-order stage.

ASTM vs. ISO Stainless Steel Thickness Tolerances

ASTM and ISO are both widely used in international metal procurement.

However, their structure and terminology differ.

These systems should not be mixed without a documented technical agreement.

Can ASTM and ISO Tolerances Be Used Interchangeably?

Not automatically.

Even when the specified thickness and width are identical, allowable deviations and measurement requirements can differ.

A sheet that meets one dimensional specification may not necessarily meet another.

For an export project, the purchase order should identify one governing standard or clearly define how multiple requirements are to be applied.

Which Standard Should Overseas Buyers Choose?

The answer depends on the project’s design specifications, destination market, end-user requirements, and available material.

ASTM standards are common in North American and international industrial procurement.

ISO and EN standards are common in European and global projects.

The most important requirement is that the supplier and purchaser agree on the exact applicable standard and edition.

Cold-Rolled vs. Hot-Rolled Stainless Steel Tolerances

The manufacturing route has a major influence on stainless steel dimensions, surface finish, and tolerance requirements.

Cold-Rolled Stainless Steel Sheet

Cold-rolled stainless steel sheet is processed to its final thickness through cold reduction and associated finishing operations.

It is commonly used for:

• Appareils
• Kitchen equipment
• Decorative sheet
• Sheet-metal enclosures
• Precision fabrication
• Components requiring a relatively smooth surface

Cold-rolled products often offer better thickness control and surface finish than comparable hot-rolled products.

However, the actual tolerance must still be specified.

Hot-Rolled Stainless Steel Sheet and Plate

Hot-rolled stainless steel is processed at elevated temperatures.

It is widely used for industrial plate, heavy equipment, tanks, structural components, and other demanding applications.

Hot-rolled stainless products may have different surface characteristics and tolerance requirements than cold-rolled sheet.

Continuous Hot-Rolled Plate vs. Quarto Plate

A critical distinction is the production route.

Continuously hot-rolled sheet/plate is produced through a continuous rolling route.

Quarto plate is produced on a reversing plate mill.

These products should not automatically use the same dimensional tolerance tables.

ISO 18286 covers specified hot-rolled stainless quarto plates with nominal thicknesses from 4 mm to 250 mm and nominal widths of at least 600 mm.

It does not apply to every product commercially described as a plate.

Why Quarto Plate Tolerances Are Different

Heavy plate production involves different rolling and dimensional-control conditions.

The tolerance requirements may include asymmetric upper and lower deviations.

Therefore, an ISO 9445 cold-rolled sheet tolerance chart should never be used to evaluate heavy quarto plate simply because both products are made from stainless steel.

304 vs. 316L Stainless Steel Sheet Thickness

304 and 316L are two widely used austenitic stainless steel grades.

The main difference between them is chemical composition and corrosion-related performance, not a separate universal thickness gauge system.

Does Stainless Grade Affect Thickness Tolerance?

A stainless steel grade does not by itself determine every dimensional tolerance.

For example, if 304 and 316L sheets are supplied under the same applicable flat-product dimensional specification, using the same product form and dimensions, they may be subject to the same thickness-tolerance provisions.

However, different material conditions, product forms, or special requirements can change the applicable rules.

304 FEUILLE D'AREILLEMENT INOXED

304 is widely used for general industrial fabrication, equipment, architectural components, and applications requiring a balance of corrosion resistance and manufacturability.

For purchasing options, see tôle d'acier inoxydable 304.

316L Stainless Steel Sheet and Coil

316L contains molybdenum and generally provides improved resistance to localized chloride corrosion compared with 304.

It is commonly used for chemical equipment, selected process systems, and applications requiring higher corrosion resistance.

Explorez notre Bobine en acier inoxydable 316L product information.

Is 1 mm 304 Stainless Steel Stronger Than 1 mm 316L?

This is a separate mechanical-properties question.

Thickness alone does not determine material strength.

The required sheet thickness must consider:

• Applied load
• Support spacing
• Material yield strength
• Allowable deflection
• Forming requirements
• Corrosion allowance, where applicable
• Design code or application requirements

Thickness tolerance defines acceptable manufacturing variation. It does not replace engineering design calculations.

Thickness Tolerance vs. Width and Length Tolerance

Stainless steel sheet procurement requires more than thickness control.

Width and length tolerances are also important, especially for automated cutting, stamping, and assembly.

Width Tolerance

Actual sheet width may differ from the specified width within the limits allowed by the relevant standard.

The requirement may depend on:

• Forme du produit
• Épaisseur
• Specified width
• Mill edge or slit edge
• Normal or special tolerance

Some standards use positive-only width tolerances for certain products.

Therefore, do not assume every width specification uses a symmetrical tolerance.

Mill Edge vs. Slit Edge

Mill Edge

An edge retained from the rolling process without subsequent longitudinal trimming.

Slit Edge

An edge produced by slitting the material to a required width.

La distinction est importante car l’état des bords peut affecter les exigences applicables en matière de largeur et de mesure.

Tolérance à la longueur

Les tôles inoxydables coupées à longueur peuvent être soumises à des tolérances de longueur positives uniquement selon certaines spécifications.

Une longueur nominale de 2 438 mm n'implique pas nécessairement une variation symétrique ±.

Le bon de commande doit indiquer si les tolérances de longueur standard sont suffisantes ou si des exigences spéciales de coupe à longueur sont nécessaires.

Quand des dimensions spéciales sont-elles nécessaires ?

Un contrôle des dimensions plus restrictif peut être requis pour :

• Boîtiers pour équipements de précision
• Production automatisée
• Assemblages ajustés
• Grands panneaux architecturaux
• Ébauches de composants découpées au laser
• Produits avec une marge de coupe limitée

Lorsque des tolérances particulières sont requises, confirmez la faisabilité de la fabrication avant de passer la commande.

Planéité, cambrure des bords et équerrage

Thickness is only one part of stainless steel dimensional quality.

A sheet can satisfy its thickness tolerance and still create fabrication problems because of poor flatness or geometry.

Platitude

Flatness describes how closely a sheet conforms to a flat reference surface.

Poor flatness can affect:

• Laser cutting
• CNC punching
• Automated feeding
• Welding fixtures
• Large panel installation
• Assembly tolerances

A specified flatness tolerance should identify the applicable measurement method and acceptance conditions.

Edge Camber

Edge camber is the deviation of a strip edge from a straight reference line over a specified length.

It matters in:

• Coil slitting
• Automated feeding
• Roll forming
• Progressive stamping
• Strip processing

Excessive edge camber can create tracking problems during production.

Squareness

Squareness concerns whether the edges of a cut sheet form the required rectangular geometry.

It can be assessed using specified dimensional methods, including differences between diagonal lengths where the applicable standard permits.

For fabricated assemblies, squareness may matter as much as thickness.

Edge Waviness

Edge waviness describes repeated wave-like distortions along the edge of sheet or strip.

This can influence flatness, feeding, and forming performance.

When sheet appearance or precision fabrication is critical, specify the required flatness and edge quality rather than relying only on thickness.

How to Measure Stainless Steel Sheet Thickness Correctly

Thickness inspection should follow a consistent procedure.

An incorrectly measured sheet may be accepted or rejected for the wrong reasons.

1. Select the Appropriate Measuring Instrument

Common instruments include:

• Digital outside micrometer
• Mechanical micrometer
• Suitable precision thickness gauge
• Calibrated thickness-measuring equipment

The selected instrument should have sufficient resolution, accuracy, measuring-force control, and an appropriate measurement range.

For example, a calibrated digital micrometer with 0.001 mm resolution may be useful for thin sheet inspection, provided the instrument’s actual measurement uncertainty is suitable for the required tolerance.

Resolution is not the same as accuracy.

2. Check Calibration

Before measurement, confirm that the instrument is calibrated and suitable for the inspection.

Check the measuring faces and zero setting.

Any instrument defect, contamination, or incorrect zero setting may affect the result.

3. Clean the Measuring Surfaces

Remove loose debris, oil deposits, and particles that could interfere with contact between the measuring instrument and the stainless steel.

Do not alter the product or remove required coatings without an agreed inspection procedure.

4. Identify Measurement Locations

Measurement locations must follow the applicable standard.

For example, ISO 9445-2 Method A and Method B prescribe different distances from the edges.

A generic practice of measuring only at the sheet edge is not an adequate substitute for these requirements.

For additional quality control, the purchaser and supplier may agree on a sampling plan covering multiple locations.

5. Measure at Multiple Points

Depending on the inspection plan, measurements may be taken at several positions across the sheet.

A representative internal QC plan could include points near the center and different areas across the product, while respecting standard-defined measurement exclusions.

These additional points can help identify thickness variation.

Cependant, an average thickness within tolerance does not mean every individually regulated measurement is acceptable.

Each required measurement must satisfy the applicable acceptance criteria.

6. Record the Measurements

A thickness inspection record may include:

This example is illustrative and assumes the locations and product conditions conform to the specified standard. It is not an actual Steel1Stop inspection report.

7. Evaluate the Results

Compare each applicable measurement with the specified tolerance limits.

If measurements fall outside the required limits, follow the agreed inspection, verification, and nonconformance procedures.

Do not automatically approve material based only on a batch average.

Why Sheet Thickness Tolerance Matters in Manufacturing

Thickness variation may affect manufacturing in different ways.

Coupure laser

Cutting settings depend partly on material thickness.

Changes in thickness can influence cutting speed, cut quality, and process stability.

For precision components, material variability should be considered during process planning.

Press Brake Bending

Sheet thickness is a major input in bending calculations.

It affects:

• Bend allowance
• Bend deduction
• Required force
• Tooling selection
• Inside bend geometry
• Dimensional repeatability

A bending program developed for one sheet thickness may produce different results if the actual material thickness changes.

Soudage

Different sheet thicknesses can require adjustments to welding parameters and joint design.

Thickness variation may affect heat input requirements and dimensional distortion.

Equipment Enclosures

Sheet-metal equipment enclosures often require accurate fit between panels, frames, fasteners, and formed components.

Unexpected material thickness can cause clearance or alignment problems.

Pressure Equipment

For pressure-related applications, design calculations may depend on minimum required wall or plate thickness.

An acceptable nominal purchasing thickness does not necessarily satisfy the minimum-thickness design requirement.

The design code, material standard, corrosion allowance, and fabrication requirements must be considered.

How Thickness Tolerance Affects Sheet Weight and Cost

Stainless steel is often purchased by weight.

Thickness therefore affects theoretical sheet weight and the amount of material supplied.

Stainless Steel Sheet Weight Formula

For a rectangular sheet:

Weight (kg) = Thickness (mm) × Width (mm) × Length (mm) × Density (g/cm³) ÷ 1,000,000

For a calculation using a density of 8.00 g/cm³:

Weight (kg) = Thickness × Width × Length × 8.00 ÷ 1,000,000

The exact density varies with stainless steel grade.

Example: 304 Stainless Steel Sheet

Assume:

• Thickness: 1.00 mm
• Largeur : 1219 mm
• Longueur : 2438 mm
• Density: 8.00 g/cm³

The theoretical weight is:

1.00 × 1219 × 2438 × 8.00 ÷ 1,000,000

Theoretical weight ≈ 23.78 kg per sheet

Effect of Thickness Variation

Using the same width, length, and density:

This example illustrates how a 5% change in thickness results in approximately a 5% change in theoretical sheet weight when the other variables remain constant.

It does not establish the permitted thickness range under a particular standard.

What Is the Weight per Square Meter?

For a density of 8.00 g/cm³:

These are theoretical values based on the stated density.

Actual shipment weight can differ due to actual thickness, actual dimensions, material density, and other factors.

Does Lower Actual Thickness Mean Lower Purchase Cost?

Pas nécessairement.

Commercial pricing depends on the agreed pricing basis.

Some orders are quoted per metric ton.

Others may be quoted per sheet, per piece, or per processed component.

Buyers should understand whether the quoted price is based on:

• Theoretical weight
• Actual measured weight
• Sheet count
• Processed parts
• Agreed invoicing quantity

The contract should define the pricing basis and weight-verification arrangements.

Standard vs. Precision Thickness Tolerance

Tighter tolerances can improve consistency, but they may also increase manufacturing difficulty and cost.

When Standard Tolerance May Be Sufficient

Normal tolerance requirements are often appropriate for general fabrication when the product design can accommodate the allowed dimensional variations.

Typical considerations include:

• General sheet-metal components
• Non-precision covers
• Industrial fabrication
• Panneaux décoratifs
• Components with sufficient assembly clearance

When Special Tolerances May Be Required

More restrictive tolerances may be justified for:

• Precision stamping
• Close-tolerance forming
• Automated coil feeding
• Critical equipment components
• Controlled assembly clearances
• Special minimum-thickness requirements

How to Request a Tighter Tolerance

A request should state:

1. Applicable material and dimensional standard
2. Épaisseur spécifiée
3. Required tolerance class or agreed limits
4. Product width
5. Required measurement method
6. Sampling and inspection requirements
7. Minimum acceptable actual thickness, if applicable

Do not assume that every sheet size or grade is commercially available with the same precision tolerance.

How to Specify Stainless Steel Sheet Thickness in an RFQ

A well-written Request for Quotation reduces ambiguity between the buyer and supplier.

The request should define the material, dimensions, manufacturing standard, tolerance requirements, and inspection expectations.

Stainless Steel Sheet RFQ Checklist

Example RFQ: 304 Stainless Steel Sheet

A suitable quotation request might read:

Produit : Tôle d'acier inoxydable 304
Catégorie : UNS S30400
Norme matérielle : ASTM A240/A240M
Exigences générales : ASTM A480/A480M
Thickness: 1.00 mm
Largeur : 1219 mm
Longueur : 2438 mm
Terminer : 2B
Edge: As agreed
Thickness Tolerance: According to applicable metric specification
Quantité : 500 feuilles
Documentation: Mill Test Certificate
Inspection: Dimensions, thickness and surface condition
Packing: Export packaging
Destination : A conseiller

If the project requires a guaranteed minimum thickness, specify that requirement separately.

Par exemple:

Minimum actual thickness: 1.00 mm at the locations and under the conditions defined in the approved inspection specification.

This requirement must be agreed with the supplier, and may call for a different nominal order thickness.

Should Buyers Specify ASTM or ISO?

Choose the system required by the project or end customer.

Avoid writing unclear specifications such as:

“ASTM / ISO tolerance, standard quality.”

Instead, identify the specific applicable standard and edition.

For custom projects, Steel1Stop can review drawings and material requirements before confirming a suitable supply and processing route.

See our customized steel solutions page for project-based material requirements.

Incoming Inspection and Material Acceptance

Incoming inspection helps buyers verify that delivered stainless steel matches their purchase order.

The inspection plan should be established before shipment or receipt.

Step 1: Verify the Material Documents

Check:

• Product description
• Grade
• Standard
• Numéro de manche
• Dimensions
• Quantité
• Required MTC
• Traceability information

Step 2: Confirm Product Identity

Verify that the delivered material matches the purchase order and relevant documentation.

For critical projects, material identification testing may be specified separately.

Step 3: Inspect Thickness

Use calibrated measurement equipment and the measurement locations required by the applicable standard.

Take the agreed number of measurements.

Compare each relevant result with the applicable acceptance limits.

Step 4: Inspect Width and Length

Measure the sheet dimensions using suitable calibrated instruments.

Check the permitted deviations under the agreed standard.

Step 5: Check Flatness and Edge Quality

Where required, inspect:

• Platitude
• Edge camber
• Squareness
• Edge damage
• Cut quality
• État des surfaces

Step 6: Inspect Packaging and Surface Protection

Confirm that the material is protected against transportation and storage damage.

For polished or decorative stainless steel, protective film and interleaving may be particularly important.

Step 7: Document Nonconformities

If the delivered material does not meet the agreed requirements, record the relevant measurements, identification, and supporting evidence.

The buyer and supplier should then follow the agreed nonconformance procedure.

A Mill Test Certificate alone is not always sufficient to verify every dimensional requirement of every delivered sheet.

Appropriate dimensional inspection may still be necessary.

Foire aux questions

What is the thickness tolerance of a 1 mm stainless steel sheet?

There is no universal value. The permitted deviation depends on the applicable standard, product form, width, rolling condition, and tolerance class.

Is 1 mm stainless steel sheet exactly 1.00 mm thick?

Not necessarily. Actual thickness may vary within the applicable manufacturing tolerance.

What is the difference between nominal and actual thickness?

Nominal or specified thickness is the ordered dimension. Actual thickness is the measured thickness of the supplied material.

What is 16 gauge stainless steel in millimeters?

A common U.S. stainless gauge chart gives 16 gauge as 0.0625 inches, approximately 1.59 mm.

What is 18 gauge stainless steel thickness?

18 gauge stainless steel is commonly equivalent to 0.0500 inches, approximately 1.27 mm.

What is the difference between stainless and mild steel gauge?

The same gauge number can represent different nominal thicknesses in stainless steel and carbon steel gauge systems.

Does ASTM A480 specify stainless steel sheet tolerances?

Yes. ASTM A480/A480M provides general requirements, including dimensional tolerances, for flat-rolled stainless products within its scope.

Is ASTM A240 the same as ASTM A480?

No. ASTM A240/A240M is primarily a material specification, while ASTM A480/A480M provides applicable general requirements.

What is ISO 9445-2?

ISO 9445-2 specifies dimensional and form tolerances for continuously cold-rolled stainless steel wide strip and sheet/plate within its defined product range.

What is the difference between ISO 9445 Method A and Method B?

The two methods use different thickness tolerance tables and measurement-location requirements.

Does 304 have a different thickness tolerance from 316L?

Not inherently. The dimensional requirements depend primarily on the applicable product and tolerance specifications, as well as the specified product conditions.

Is cold-rolled stainless steel more accurate than hot-rolled stainless steel?

Cold-rolled products commonly offer tighter dimensional control, but actual tolerances depend on the relevant standard and product specification.

Can I order stainless steel sheet with zero negative tolerance?

A special minimum-thickness requirement may be possible by agreement. The supplier must confirm the available manufacturing and tolerance options.

Where should stainless steel thickness be measured?

At locations required by the applicable standard. Some standards specify different distances from slit edges and mill edges.

Can I use an average thickness to accept a sheet?

Not if the applicable acceptance criteria require individual measurements to remain within specified limits. An acceptable average does not automatically establish compliance.

Does sheet thickness affect weight?

Yes. For fixed sheet dimensions and density, theoretical sheet weight is directly proportional to thickness.

What is the theoretical weight of a 1 mm 304 stainless steel sheet?

At a density of 8.00 g/cm³, a 1 mm thick sheet measuring 1219 × 2438 mm weighs approximately 23.78 kg.

What tolerance should I specify for laser cutting?

The required tolerance depends on the part design, material, cutting process, and assembly requirements. Confirm the applicable material tolerance and the separate finished-part requirements with the fabricator.

What is flatness tolerance?

Flatness tolerance defines the permitted deviation from a specified flat reference condition according to the applicable standard and measurement procedure.

How can I avoid receiving undersized stainless steel sheets?

Specify the applicable standard, required nominal thickness, any minimum actual thickness requirement, measurement method, and inspection criteria in the purchase order.

Final Buying Guide: Choosing the Right Stainless Steel Sheet Thickness

Selecting the correct stainless steel sheet involves more than choosing a nominal thickness.

Buyers should identify the applicable material and dimensional standards, confirm whether the product is cold-rolled or hot-rolled, and understand how the actual thickness may vary.

For purchasing, the most important principles are:

1. Specify actual dimensions. Use millimeters or decimal inches rather than relying only on Gauge.

2. Identify the governing standard. ASTM A480/A480M, ISO 9445, and other specifications have different scopes and dimensional requirements.

3. Confirm the tolerance requirements. Normal tolerance may be sufficient for general applications, while precision manufacturing can require stricter limits.

4. Consider the manufacturing process. Thickness, flatness, width and length can affect cutting, bending, welding, and assembly.

5. Establish inspection criteria. Measurement locations, instruments, sampling and acceptance limits should be defined before delivery.

At Steel1Stop, we support international customers sourcing stainless steel sheet, plate, coil, and other metal products for industrial manufacturing, fabrication, and construction projects.

Explorez notre tôle d'acier inoxydable 304, tôle d'acier inoxydable 201, et Bobine en acier inoxydable 316L product pages for relevant material information.

For customized procurement, provide the required grade, dimensions, standard, tolerance, quantity, surface finish, and inspection requirements.

A complete thickness and tolerance specification reduces purchasing uncertainty, improves manufacturing consistency, and helps ensure that delivered stainless steel meets the intended application.